flac3d5.0常用命令集锦
...wd...建 模1、调用文件：①文件与工程在同一个文件夹，只写文件名即可：If the called file is located in the same folder as the FLAC3D project file, then only the file name needbe entered with the CALL command. ②不在同一个文件夹，全路径：Otherwise, the file may be called by specifying its completepath (e.g., c:\myfolder\file.dat).Undo ;撤销上一条命令2、创立 旋转 缩放视图3、建模命令model mech mohr ;莫尔库伦模型model mech elastic ;弹性模型set grav 0, 0, -9.81 ; 重力加速度 negative z-direction. 〔垂直向下！常用的〕下面这代码，是沿着-y方向的重力加速度，注意区别！！！！gen zone brick size 6,8,8 p0 -10, -10, -20 ... ;省略号表示写不下后面继续p1 10, -10, -20 ...p2 -10, 10, -20 ...p3 -10, -10, 0plot zonegen zone brick size 6,8,8 p0 -10, -10, -20 ... ;不规则六面体p1 10, -10, -20 p2 -10, 10, -20 ...p3 -10, -10, 0 p4 10, 10, -20 ...p5 -10, 10, 10 p6 10, -10, 0 ...p7 10, 10, 10plot current plot Plot01plot clear plot zoneUndo ;撤销命令set logfile 127X1001.txtset log on truncateset log offlist zone prin range x 0 1 y 0 1 z 0 1 ;显示指定范围内各单元的主应力，结果如下Hist命令：①命令编号按顺序从1开场：each history is numbered sequentially from 1 as it is entered via the HISTORY command.②查找显示所有的his命令：Return to the Flac3D> prompt and type list hist for a listing of the histories and their corresponding numbers.hist nstep 5 ;每5步记录1次。
默认是10步记录1次hist add ratio ;记录maximum unbalanced force ratiohist add gp zdisp 4 4 8 ;记录节点的位移model null range x=2,4 y=2,6 z=5,10 ;To excavate the trench,enterThe dimensions of the excavation region (i.e., the null material) are defined by the x-, y- and z-coordinate range.set large ;设置大变形large-strain logic is specifiedini xdis 0 ydis 0 zdis 0 ;位移归零solvesave trench ; 保持计算结果的文件 “TRENCH.F3SAV〞不需要后缀4、group命令(注意新版本的区别 ，group zone)gen zone brick size 6 6 6group zone Tunnel range x 1 6 y 0 6 z 1 5 ;设置groupmodel mech mohr ; 莫尔库伦模型model mech null range group Tunnel ;group zone Tunnel range cylinder end1 100 105 100 end2 100 95 100 radius 3group zone Matrix range group Tunnel not; naming RANGES that are fixed in space and unrelated; to the model geometry - represents stratigraphy...range name Layer1 plane dip 0 dd 0 ori 0 0 0 aboverange name Layer2 plane dip 0 dd 0 ori 0 0 0 belowprop bulk 1e8 shear 0.5e8 coh 0 tens 0 fric 35 range nrange Layer1prop bulk 1e7 shear 0.3e7 coh 1e7 tens 0 fric 0 range nrange Layer2pl zone colorby group4、Interface命令以下是切割模型法生成interface：寺河模拟用的pl zone gen zone brick p0 0 0 0 p1 200 0 0 p2 0 40 0 p3 0 0 4 size 100 20 2 group 1 ; gen zone brick p0 0 0 4 p1 200 0 4 p2 0 40 4 p3 0 0 8 size 100 20 2 group 2 ; gen separate group 1interface 1 wrap first group 1 second group 2interface 1 maxedge 0.5显示interface：plot create plot Plot01plot add surface;显示外表plot add interface red;显示交互面为红色plot show用导来导去法，已经在5.0上运行过，很好，值得借鉴pl zone colorby groupgen zone brick size 3 3 3 &p0 (0,0,0) p1 (3,0,0) p2 (0,3,0) p3 (0,0,1.5) &p4 (3,3,0) p5 (0,3,1.5) p6 (3,0,4.5) p7 (3,3,4.5)group zone Basegen zone brick size 3 3 3 &p0 (0,0,2.5) p1 (3,0,5.5) p2 (0,3,2.5) p3 (0,0,7) &p4 (3,3,5.5) p5 (0,3,7) p6 (3,0,7) p7 (3,3,7)group zone Top range group Base notinterface 1 face range plane norm (-1,0,1) origin (1.5,1.5,3) dist 0.1pl add interfacepauseini zpos add -1.0 range group Top4、hist命令(5.0版本需要加add！！！)hist nstep=5 //设置采用间隔为5 等效于set hist_rep=5hist add id =2 zone szz 0,0,-1hist unbal //最大非平衡力hist add gp zdisp 4 4 8 print histhist add gp zdis 0,0,0hist add gp zvel 0,0,0hist add gp ydisp 0,0,0;监测网格点〔0，0，0〕点的y 方向上的位移hist add zone syy 0,1,0;监测单元〔0，1，0〕点的y 方向上的应力hist add zone syy 1,1,0;监测单元〔1，1，0〕点的y 方向上的应力hist add zone szz 0,0,-1List historyset largehistory nstep 2history add fish tthistory add fish thetahistory add zone sxx (1,1,1)history add zone syy (1,1,1)history add zone szz (1,1,1)plot add his 3 4 5 vs 1HISTORY addfish var;fish var变量的监测5、solve命令 ?????什么意思5、plot命令通过图形操作界面的方式：pl zone colorby gr ;查看各个分组通过命令流的方式：plot create plot Plot01plot clearplot add history 1 linestyle color blackplot post plot Plot01 file 127F1002.ps manualplot create plot Plot02plot clearplot add history 2 linestyle color blackplot post plot Plot02 file 127F1003.ps manualplot create plot GravVplot cut add plane dip 90 dd 0 origin 3,4.1,0 ;截面plot set center 3 3 3plot set eye 12 18 12plot add zone plane behindplane on onplane off ;addlabel "Zone" whiteplot add bcont szz ramp greyplot add axesplot post plot GravV file 127F1004.ps manualres kw50plot create plot szz_contourplot cut add plane dip 90 dd 180 origin 0,18.9,0plot set orient 120 220 0plot set center 45 45 0plot add zone plane behindplane on onplane off ; plot add bcont szz ramp rainbowpl set mag 1.0plot add axesplot showplot create GravVplot set plane dip=90 dd=0 origin=3,4,0plot set rot 15 0 20 ;this would be achieved interactivelyplot set center 2.5 4.2 4.0 ;and is show here simply to illustrateplot add bound behind plot add bcont szz plane plot add axes plot show这样我们就建设了一个叫“Grav V〞的图形，将它设为当前图层，对此图形设置一个倾角为90°的面，〔在x-y面上，约定z的负方向为下〕，倾向为0°。
〔在x-y面上，从y的正方向开场沿顺时针方向计量〕，过x-y面上一点〔x=3,y=4,z=0〕,在平面后加一个网格，垂直方向的应力Qzz，最后给模型加轴线，整体图形轮廓与添加图形相反，显示每个区域中心的应力计算值，每个区域的颜色直接对应 根本区域的应力，当键入show,我们建设的图形被显示 Plot create DispcontPl add cont disp plane behindPl add axesPl show plot sketch;绘出轮廓线plot add vel;添加矢量plot add his 1 2 vs 3;绘出历史记录n，actLoad ， p_solcyc 15000plot Create TrenchAdd surface yellowAdd axes blackShowplot create szz_contour;创立文件名为szz_contour〔z 方向的应力云图〕plot set cent 4 4 5;视图的中心坐标为〔4，4，5〕plot set rot 20 0 30;视图的旋转角度为〔20，0，30〕plot set mag 1.0;视图的放大倍数为1.0plot add cont szz out on shade on;翻开szz 的等值线图plot add axes;翻开坐标轴线plot show;显示窗口;不同的区域，材料赋值不同pl zone colorby modelpl zone colorby group求解前对模型进展检查网格检查(如前所述)边界条件检查速度约束条件 plot gpfix 荷载条件 plot fap 模型检查模型赋值 plo block model参数赋值 plo block prop ***初始应力检查(如后所述)经常检查模型的响应plo zcon szz (syy, sxx) 应力场plo con zdis (ydis, xdis) 位移场plo (add) zone colorby state 屈服状态plo gpfix 速度约束条件plo fap 体力plo hist (unbal) 1 不平衡力 〔必需的〕pl set movieactive onpl set movieextension jpgpl set movieinterval 20pl set movieprefix sihekuangkaiwapl set moviesize ix iypl set name sihedacaigaopl bitmap view 1 file myplot.png pl bitmap view 1 size 1024 768pl create
该准则 根本的内涵为：岩石的剪切破坏是由岩石破裂面产生的破坏剪应力受到岩石材料的内聚力和内摩擦力的抵抗，当破裂面上的破坏剪应力大于岩石的内聚力和内摩擦力时，即 Fs>0 时，材料发生剪切破坏[4]：有限差分法(FDM)Fish函数1、 if条件从句2、 loop条件从句newdef derives_mod = y_mod / (2.0 * (1.0 + p_ratio))b_mod = y_mod / (3.0 * (1.0 - 2.0 * p_ratio))endset @y_mod=5e8 @p_ratio=0.25@derivelist @b_mod @s_modgen zone brick size (2,2,2)model mech elasticprop bulk=@b_mod shear=@s_modlist zone prop bulklist zone prop shearnewdef xxxsum = 0prod = 1loop n (1,10)sum = sum + nprod = prod * nend_loopend@xxxlist @sum @prodnewdef abcif xx > 0 thenabc = 33elseabc = 11end_ifendset @xx=1list @abcset @xx=-1list @abcnewgen zone brick size 10 3 5def place_cablesloop n (1,5)z_d = float(n) - 0.5commandsel cable beg (0.0,1.5,@z_d) end (7.0,1.5,@z_d) nseg 7end_commandend_loopend@place_cablesplot add zone trans 75 plot add sel geomnewgen zone brick size 10 3 5model mech mohrprop bulk 1e8 shear 0.3e8 fric 35prop coh 1e3 tens 1e3ini dens 1000set grav (0,0,-10); ; 重力加速度fix x y z range z 0.0fix y range y 0.0fix y range y 3.0fix x range x 0.0fix x range x 10.0set largehist add unbalsolvesave cab_strini xdis 0 ydis 0 zdis 0hist add gp xdisp (0,1,5)def place_cablesloop n (1,5)z_d = 5.5 - float(n)z_t = z_d + 0.5z_b = z_d - 0.5commandfree x range x 0.0 z @z_b,@z_tsolvesel cable beg (0.0,0.5,@z_d) end (7.0,0.5,@z_d) nseg 7sel cable beg (0.0,1.5,@z_d) end (7.0,1.5,@z_d) nseg 7sel cable beg (0.0,2.5,@z_d) end (7.0,2.5,@z_d) nseg 7sel cable prop emod 2e10 ytension 1e8 xcarea 1.0 ...gr_k 2e10 gr_coh 1e10 gr_per 1.0end_commandend_loopend@place_cablessave cab_endplot zone trans 75 sel cabblock force line width 4newgen zone brick size 1 2 1model mech mohrprop shear=1e8 bulk=2e8 ...cohes=1e5 tens=1e10fix x y z range y 0.0apply yvel -1e-5 range y 2.0def get_adad1 = gp_near(0,2,0)ad2 = gp_near(1,2,0)ad3 = gp_near(0,2,1)ad4 = gp_near(1,2,1)end@get_addef loadload=gp_yfunbal(ad1)+gp_yfunbal(ad2)+gp_yfunbal(ad3)+gp_yfunbal(ad4)endhist add fish loadhist add gp ydis (0,6,0)step 1000plot his 1 vs -2newgen zone brick size 10 3 5model mech mohrprop bulk 1e8 shear 0.3e8 fric 35prop coh 1e3 tens 1e3ini dens 1000set grav (0,0,-10); ; 重力加速度fix x y z range z 0.0fix y range y 0.0fix y range y 3.0fix x range x 0.0fix x range x 10.0set large; ;大变形hist add unbalsolvesave cab_str; ;保持计算结果文件，不用加后缀名.Savini xdis 0 ydis 0 zdis 0; ; 位移归零hist add gp xdisp (0,1,5)def place_cablesloop n (1,5)z_d = 5.5 - float(n)z_t = z_d + 0.5z_b = z_d - 0.5commandfree x range x 0.0 z @z_b,@z_tsolvesel cable beg (0.0,0.5,@z_d) end (7.0,0.5,@z_d) nseg 7sel cable beg (0.0,1.5,@z_d) end (7.0,1.5,@z_d) nseg 7sel cable beg (0.0,2.5,@z_d) end (7.0,2.5,@z_d) nseg 7sel cable prop emod 2e10 ytension 1e8 xcarea 1.0 ...gr_k 2e10 gr_coh 1e10 gr_per 1.0end_commandend_loopend@place_cablessave cab_endplot zone trans 75 sel cabblock force line width 4def parmglobal rad=4.0 ; radius of spherical cavityglobal len=10.0 ; length of outer box edgeglobal in_size=6 ; number of zones along outer cube edgeglobal rad_size=10 ; number of zones in radial directionend@parmgen zone radbrick edge @len size @in_size @in_size @in_size @rad_size &rat 1.0 1.0 1.0 1.2 dim @rad @rad @raddef mountainlocal gp = gp_headloop while gp # nulllocal zz = sqrt(gp_xpos(gp)^2 + gp_ypos(gp)^2)local dz = 0.06 * sin(0.2 * zz + 100.0) ; Sum Fourier terms fordz = dz + 0.06 * sin(0.22 * zz - 20.3) ; quasi-random surfacedz = dz - 0.04 * sin(0.33 * zz + 33.3) ; topology.gp_zpos(gp) = 0.5 * gp_zpos(gp) * (1.0 + dz)gp = gp_next(gp)end_loopend@mountainfix x range x -.1 .1fix x range x 99.9 100.1fix y range y -.1 .1fix y range y 99.9 100.1fix z range z -.1 .1set grav 0,0,-10ini density=2000ini szz=-2.0e6 (grad 0,0,2.0e4) ini sxx=-4.0e6 (grad 0,0,4.0e4) syy=-4.0e6 (grad 0,0,4.0e4)solvedefine afill ; fill matrix with random numbersarray var(4,3)local mloop m (1,4)local nloop n (1,3)var(m,n) = urandend_loopend_loopendnewdefine h_var_1local zi = z_near(1,1,1)h_var_1 = z_sxx(zi)h_var_2 = z_syy(zi)h_var_3 = z_szz(zi)endThe FLAC3D commands to request histories might behist add fish h var 1hist add fish h var 2hist add fish h var 3degrade您好，欢送您阅读我的文章，本WORD文档可编辑修改，也可以直接打印。
阅读过后，希望您提出保贵的意见或建议阅读和学习是一种非常好的习惯，坚持下去，让我们共同进步。
